Journal Entry
 |
Visit GILBERT (Gil) DUPRE (ret Electrical Engineer)'s Profile. Subscribe to this Journal: 
What is RSS?
There are 80 entries in this Journal. Status: Member Location: CHATTANOOGA, TN, USA |
|
Moss AC Kit In 74.5
Created on 2008-05-31 14:52:43
Well I believe I have it cooling as well as can be expected at 1400 rpm low press is about 35 and high is about 175 psi. at 2500 rpm and above low press drops to about 30 and high press goes to about 190. Outside air was 86 deg f.Temp at outlet of center vent is 50 deg f and about 55 to 60 at the other vents. Felt hot air coming in thru the fresh air vents so closed them off but couldnt completely shut off. Will work on that problem.
Only problem is temp gauge goes to about half way between N and H. Ill work on that but it controlabled for now and not toooooo hot.
Only problem is temp gauge goes to about half way between N and H. Ill work on that but it controlabled for now and not toooooo hot.
Summary of Previous Journal Entries
Showing previous 10 journal entries:
| Title | Date | #Pic | #Cmt | Excerpt |
|---|---|---|---|---|
| Audiovox Cruise Control | 2008-04-17 | 1 | I finally connected all the wires that I left hanging from last fall while I installed the Moss AC. Today I took it out and checked the cruise control and man will that be nice thi... | |
| Moss AC Kit In 74.5 | 2008-02-02 | 1 | Finished editing the proceedure I used to get the kit to work in the 74.5 GT. More than 12 hours and more $$$$. Maybe I can trade something for it from Moss hahahaha. | |
| Got It Running | 2008-01-27 | Got the carb fuel leak fixed thanks to Jimmie then found a hose leaking. Got it fixed. started it up and drove around the block was running rough. Lots of dust needs clean... | ||
| Fired Up MGA | 2008-01-14 | After in paint for 2 months I decided to start it up. I have to take it back for color sand and compound. Battery was dead charged for two days no luck. Put on booster battery and ... | ||
| MGA Fender Piping | 2008-01-02 | Got one side of new piping fitted with slots cut for fender mtg bolts. Next re aligning fender to door and body and bolting down. What a job. | ||
| MC Replacement | 2008-01-01 | I completed the MC and Clutch MC replacement and took it for test drive. Clutch works great but I need to maybe bleed brakes again. | ||
| Brakes | 2007-12-30 | Finished brake and clutch MC's replacement. SS brake and clutch hoses and both master cylinders. Replaced fluid with silicone dot 5 fluid. Flushed and bled all lines. | ||
| SS Brake Line | 2007-12-23 | Well today I made more progress. I installed the driver side ss brake line. One day or days I will have to replace the front suspension rubber. It is still there after 33 years. A... | ||
| New Brake Line | 2007-12-11 | Today I installed the new ss brake line on the front passenger side. It looks like it will be long enough. Getting it to loop up and to the rear was finally accomplished by adjusti... | ||
| MC Continued | 2007-12-06 | 1 | For the last few days since the last entry I have been cleaning and installing MC box support. Today I hung the pedals. Waiting on failure swithch kit. Here is the progress photo |
The contents of this journal entry (including entry images) are released
under the terms of the Creative Commons License unless otherwise noted.
under the terms of the Creative Commons License unless otherwise noted.
This page last modified December 01 2007 20:50:32 pm
Add a comment to this journal entry:
Please sign in if you already have an account or register now to enable this feature.